Battery eliminator circuit (BEC) - Revision history

Chklnk: Add Malenki which technically has a 3.3v BEC

2024-05-31T04:52:15Z

Add Malenki which technically has a 3.3v BEC

← Older revision		Revision as of 04:52, 31 May 2024
Line 14:		Line 14:
	Many [[ESCs\|electronic speed controllers]], such as the RobotPower Wasp and the FingerTech TinyESC, include a BEC circuit that feeds 5 volts back to the receiver. The amount of current provided is sufficient to operate a standard R/C receiver, but may be insufficient to operate a receiver with telemetry - particularly when used with a high source voltage. Built-in BECs generally do not provide enough power to operate servos connected to the Rx.		Many [[ESCs\|electronic speed controllers]], such as the RobotPower Wasp and the FingerTech TinyESC, include a BEC circuit that feeds 5 volts back to the receiver. The amount of current provided is sufficient to operate a standard R/C receiver, but may be insufficient to operate a receiver with telemetry - particularly when used with a high source voltage. Built-in BECs generally do not provide enough power to operate servos connected to the Rx.

	One way to get around this limitation is to use a servo that is rated for the full battery voltage, and powering the servo from that voltage instead of 5 volts.		One way to get around this limitation is to use a servo that is rated for the full battery voltage, and powering the servo from that voltage instead of 5 volts. For example, small bots such as 150g weight class can use a Malenki Nano or similar device. It's a combination '''BEC + receiver + ESC''', and any connected motors and servos are run on the full battery voltage.

	=Standalone BECs=		=Standalone BECs=

Chklnk: Higher voltage servo comment

2021-12-02T07:25:16Z

Higher voltage servo comment

← Older revision		Revision as of 07:25, 2 December 2021
Line 5:		Line 5:
	For several decades, most digital electronic circuits were made to operate using a steady 5 volt (5V) supply of power. Few batteries, or combinations of cells, equal exactly 5V, so in radio-control systems the radio receivers (Rx) and servos are forgiving, and may work just fine on as little as 4V or as much as 6.5V.		For several decades, most digital electronic circuits were made to operate using a steady 5 volt (5V) supply of power. Few batteries, or combinations of cells, equal exactly 5V, so in radio-control systems the radio receivers (Rx) and servos are forgiving, and may work just fine on as little as 4V or as much as 6.5V.

	Unfortunately these circuits can be damaged by higher voltages, and the LiPo batteries used in combat robotics are usually a minimum of 7.4V, with larger battery packs much higher. A BEC is a small voltage regulator circuit connected to the full voltage of the battery, which delivers a steady voltage so that the digital electronics operate correctly.		Unfortunately these circuits can be damaged by higher voltages, and the LiPo batteries used in combat robotics are usually a minimum of 7.4V, with larger battery packs much higher. A BEC is a small voltage regulator circuit connected to the full voltage of the battery, which delivers a steady voltage so that the digital electronics operate correctly. This eliminates the need to use two separate batteries (one for the electronics and another for motors or other devices).

	Two types of circuits are used to regulate voltage for a BEC:		Two types of circuits are used to regulate voltage for a BEC:
Line 13:		Line 13:
	=BECs built into ESCs=		=BECs built into ESCs=
	Many [[ESCs\|electronic speed controllers]], such as the RobotPower Wasp and the FingerTech TinyESC, include a BEC circuit that feeds 5 volts back to the receiver. The amount of current provided is sufficient to operate a standard R/C receiver, but may be insufficient to operate a receiver with telemetry - particularly when used with a high source voltage. Built-in BECs generally do not provide enough power to operate servos connected to the Rx.		Many [[ESCs\|electronic speed controllers]], such as the RobotPower Wasp and the FingerTech TinyESC, include a BEC circuit that feeds 5 volts back to the receiver. The amount of current provided is sufficient to operate a standard R/C receiver, but may be insufficient to operate a receiver with telemetry - particularly when used with a high source voltage. Built-in BECs generally do not provide enough power to operate servos connected to the Rx.

			One way to get around this limitation is to use a servo that is rated for the full battery voltage, and powering the servo from that voltage instead of 5 volts.

	=Standalone BECs=		=Standalone BECs=

Chklnk: Fixed 'How it works' too wordy

2021-06-24T05:51:33Z

Fixed 'How it works' too wordy

← Older revision		Revision as of 05:51, 24 June 2021
Line 3:		Line 3:

	=How it works=		=How it works=
	For several decades, most digital electronic circuits were made to operate using a steady 5 volt (5V) supply of power. ~~There are very few~~ batteries, or combinations of cells, ~~that~~ equal exactly 5V, so in radio-control systems ~~you may see fairly forgiving~~ radio receivers (Rx) and servos ~~that~~ are ~~supposed to be operated with 5 volts~~, ~~but which~~ work just fine on as little as 4V or as much as 6.5V.		For several decades, most digital electronic circuits were made to operate using a steady 5 volt (5V) supply of power. Few batteries, or combinations of cells, equal exactly 5V, so in radio-control systems the radio receivers (Rx) and servos are forgiving, and may work just fine on as little as 4V or as much as 6.5V.

	Unfortunately these circuits can be damaged by higher voltages, and the LiPo batteries used in combat robotics are usually a minimum of 7.4V, with larger battery packs much higher. A BEC is a small voltage regulator circuit connected to the full voltage of the battery, which delivers a steady voltage so that the digital electronics operate correctly.		Unfortunately these circuits can be damaged by higher voltages, and the LiPo batteries used in combat robotics are usually a minimum of 7.4V, with larger battery packs much higher. A BEC is a small voltage regulator circuit connected to the full voltage of the battery, which delivers a steady voltage so that the digital electronics operate correctly.
Line 9:		Line 9:
	Two types of circuits are used to regulate voltage for a BEC:		Two types of circuits are used to regulate voltage for a BEC:
	* '''Linear Regulators''' are simple and inexpensive, but are inefficient as they simply convert excess current into waste heat. Their capacity to provide current decreases with increasing source voltage. Linear regulators are the common type built into Electronic Speed Controllers (ESCs).		* '''Linear Regulators''' are simple and inexpensive, but are inefficient as they simply convert excess current into waste heat. Their capacity to provide current decreases with increasing source voltage. Linear regulators are the common type built into Electronic Speed Controllers (ESCs).
	* '''Switching Regulators''' are more complex circuits that very rapidly turn the ~~souce~~ voltage on and off to maintain a stable level, avoiding current waste. Switching regulators are the common type found in standalone BECs.		* '''Switching Regulators''' are more complex circuits that very rapidly turn the source voltage on and off to maintain a stable level, avoiding current waste. Switching regulators are the common type found in standalone BECs.

	=BECs built into ESCs=		=BECs built into ESCs=
	Many [[ESCs\|electronic speed controllers]], such as the RobotPower Wasp and the FingerTech TinyESC, include a BEC circuit that feeds 5 volts back to the receiver. The amount of current provided is sufficient to operate a standard R/C receiver, but may be insufficient to operate a receiver with telemetry - particularly when used with a high ~~souce~~ voltage. Built-in BECs generally do not provide enough power to operate servos connected to the Rx.		Many [[ESCs\|electronic speed controllers]], such as the RobotPower Wasp and the FingerTech TinyESC, include a BEC circuit that feeds 5 volts back to the receiver. The amount of current provided is sufficient to operate a standard R/C receiver, but may be insufficient to operate a receiver with telemetry - particularly when used with a high source voltage. Built-in BECs generally do not provide enough power to operate servos connected to the Rx.

	=Standalone BECs=		=Standalone BECs=
Line 19:		Line 19:
	=Troubleshooting the BEC=		=Troubleshooting the BEC=
	*If your Rx is not powered at all (no lights, for instance), make sure there is at least one BEC connected and providing power.		*If your Rx is not powered at all (no lights, for instance), make sure there is at least one BEC connected and providing power.
	*Avoid connecting multiple BECs to the same Rx, unless they are designed to operate that way. Disconnect all but one 5V supply wire to the Rx. Don't disconnect Ground wires; they are still needed. Also, don't disconnect the 5V wires that provide power from the Rx to servo(s).		*Avoid connecting multiple BECs to the same Rx, unless they are designed to operate that way. Disconnect all but one 5V supply wire to the Rx. Don't disconnect any Ground wires; they are still needed. Also, don't disconnect the 5V wires that provide power from the Rx to the servo(s).
	*If the Rx lights are on, but its behavior is erratic, ~~use~~ a voltmeter to measure the voltage across 5V and Ground terminals on the Rx. (Many Rx will also report their voltage back to the transmitter, which can display it on a screen.)		*If the Rx lights are on, but its behavior is erratic, you may experience temporary or intermittent loss of remote control. Use a voltmeter to measure the voltage across 5V and Ground terminals on the Rx. (Many Rx will also report their voltage back to the transmitter, which can display it on a screen.)
	*If the Rx is working correctly, but the servo(s) are not, the voltage may be just low enough (below 4.8V) that most servos will not operate. Consider adding a standalone BEC, or using a servo that can run on a higher voltage, and therefore get its power directly from the battery.		*If the Rx is working correctly, but the servo(s) are not, the voltage may be just low enough (below 4.8V) that most servos will not operate. Consider adding a standalone BEC, or using a servo that can run on a higher voltage, and therefore get its power directly from the battery.

Chklnk: Add photo to illustrate ye olde days

2021-06-23T05:43:27Z

Add photo to illustrate ye olde days

← Older revision		Revision as of 05:43, 23 June 2021
Line 1:		Line 1:
	A '''battery eliminator circuit''' (BEC) accepts battery voltage and provides a lower voltage for other circuits, such as the receiver (Rx) or the [[Servos]]. It is so named because it eliminates the need to have a second ~~battery (often called the~~ "receiver battery") of a different voltage.		[[File:Rx batt vintage.jpg\|thumb\|right\|Vintage photo by Grant Imahara shows receiver plugged into its own 4.8 volt receiver battery on the bench.]]
			A '''battery eliminator circuit''' (BEC) accepts battery voltage and provides a lower voltage for other circuits, such as the receiver (Rx) or the [[Servos]]. It is so named because it eliminates the need to have a second "receiver battery" of a different voltage.

	=How it works=		=How it works=

Satchmo: Added info on linear vs. switching regulators and warning on power consumption by telemetry receivers.

2021-06-04T21:56:46Z

Added info on linear vs. switching regulators and warning on power consumption by telemetry receivers.

← Older revision		Revision as of 21:56, 4 June 2021
Line 5:		Line 5:

	Unfortunately these circuits can be damaged by higher voltages, and the LiPo batteries used in combat robotics are usually a minimum of 7.4V, with larger battery packs much higher. A BEC is a small voltage regulator circuit connected to the full voltage of the battery, which delivers a steady voltage so that the digital electronics operate correctly.		Unfortunately these circuits can be damaged by higher voltages, and the LiPo batteries used in combat robotics are usually a minimum of 7.4V, with larger battery packs much higher. A BEC is a small voltage regulator circuit connected to the full voltage of the battery, which delivers a steady voltage so that the digital electronics operate correctly.

			Two types of circuits are used to regulate voltage for a BEC:
			* '''Linear Regulators''' are simple and inexpensive, but are inefficient as they simply convert excess current into waste heat. Their capacity to provide current decreases with increasing source voltage. Linear regulators are the common type built into Electronic Speed Controllers (ESCs).
			* '''Switching Regulators''' are more complex circuits that very rapidly turn the souce voltage on and off to maintain a stable level, avoiding current waste. Switching regulators are the common type found in standalone BECs.

	=BECs built into ESCs=		=BECs built into ESCs=
	Many [[ESCs\|electronic speed controllers]], such as the RobotPower Wasp and the FingerTech TinyESC, include a BEC circuit that feeds 5 volts back to the receiver. The amount of ~~power~~ provided ~~should run any modern Rx~~, but ~~it might~~ not be enough to ~~also run~~ servos connected to the Rx.		Many [[ESCs\|electronic speed controllers]], such as the RobotPower Wasp and the FingerTech TinyESC, include a BEC circuit that feeds 5 volts back to the receiver. The amount of current provided is sufficient to operate a standard R/C receiver, but may be insufficient to operate a receiver with telemetry - particularly when used with a high souce voltage. Built-in BECs generally do not provide enough power to operate servos connected to the Rx.

	=Standalone BECs=		=Standalone BECs=

Chklnk: BEC basic explanations and help

2021-06-02T04:16:38Z

BEC basic explanations and help

New page

A '''battery eliminator circuit''' (BEC) accepts battery voltage and provides a lower voltage for other circuits, such as the receiver (Rx) or the [[Servos]]. It is so named because it eliminates the need to have a second battery (often called the "receiver battery") of a different voltage.

=How it works=
For several decades, most digital electronic circuits were made to operate using a steady 5 volt (5V) supply of power. There are very few batteries, or combinations of cells, that equal exactly 5V, so in radio-control systems you may see fairly forgiving radio receivers (Rx) and servos that are supposed to be operated with 5 volts, but which work just fine on as little as 4V or as much as 6.5V.

Unfortunately these circuits can be damaged by higher voltages, and the LiPo batteries used in combat robotics are usually a minimum of 7.4V, with larger battery packs much higher. A BEC is a small voltage regulator circuit connected to the full voltage of the battery, which delivers a steady voltage so that the digital electronics operate correctly.

=BECs built into ESCs=
Many [[ESCs|electronic speed controllers]], such as the RobotPower Wasp and the FingerTech TinyESC, include a BEC circuit that feeds 5 volts back to the receiver. The amount of power provided should run any modern Rx, but it might not be enough to also run servos connected to the Rx.

=Standalone BECs=
There are several small and light BECs on the market that will provide 5 volts with enough current to run multiple servos and receivers. If you use one of these, be sure to disable the BEC in your ESCs (if any) by using the disable feature or by disconnecting the 5 volt wire from the ESC to the Rx.

=Troubleshooting the BEC=
*If your Rx is not powered at all (no lights, for instance), make sure there is at least one BEC connected and providing power.
*Avoid connecting multiple BECs to the same Rx, unless they are designed to operate that way. Disconnect all but one 5V supply wire to the Rx. Don't disconnect Ground wires; they are still needed. Also, don't disconnect the 5V wires that provide power from the Rx to servo(s).
*If the Rx lights are on, but its behavior is erratic, use a voltmeter to measure the voltage across 5V and Ground terminals on the Rx. (Many Rx will also report their voltage back to the transmitter, which can display it on a screen.)
*If the Rx is working correctly, but the servo(s) are not, the voltage may be just low enough (below 4.8V) that most servos will not operate. Consider adding a standalone BEC, or using a servo that can run on a higher voltage, and therefore get its power directly from the battery.